RACINGLINE UPRATED ENGINE MOTOR MOUNTS TWIN DOGBONE INSERT FOR GOLF GTI, GOLF R, AUDI S3, CUPRA LEON, OCTAVIA VRS
VWR150003 VWR150004
Lower Motor Mount
Twin Dogbone Inserts.
MQB/MQB Evo models.
Get your power to the road or track where you need it!
The Twin Dogbone Inserts fill the large voids in the factory lower engine mount with two billet inserts, limiting drivetrain movement for greatly improved strength and a much more enjoyable drive.
What do
they do?
The RacingLine upper and lower Twin Dogbone Mount Insert is one of the most affordable and transformative upgrades you can do to your MQB/MQB Evo car.
By slipping the RacingLine Twin Dogbone Insert into the voids of your factory lower engine mount you will stiffen the whole location of the drivetrain greatly to give a much tighter, sharper, more responsive feeling to your car.
Crucially, fitting both the two-piece upper and lower inserts of the RacingLine Twin Dogbone Insert eliminates the bending forces that can cause damage and ultimately failure if just one insert is fitted (as many others offer).
The RacingLine Twin Dogbone Insert limits the compliance of the lower engine mount by filling the large voids with our two billet inserts.
All of the forwards/backwards rocking movement in your drivetrain is controlled by this Lower Mount – fitment of the RacingLine Twin Dogbone Insert adds strength to the drivetrain, helping to protect from future wear and breakages.
The risk of wheel-hop under hard acceleration is almost eliminated as the whole engine and 'box assembly is firmly prevented from juddering when wheelspin occurs and through aggressive gearchages.
Fitment of the Twin Inserts will only add a minimal increase NVH to the car’s characteristics, but most keen drivers love the sense that they are more 'connected' to their car, and the gentle 'growl' that the mount conveys.
Transformed Drive
Transform the drive through eliminating wheel-hop off the line and through aggressive gearchanges - especially valuable on FWD cars.
Durability guaranteed
Unlike polyurethane or steel insert options on the market, this billet aluminum part will not deform and wear over time, and guarantees long-lasting performance.
Twin Protection
The Twin Dogbone Insert uses not one but two precision machined billet inserts to avoid the damaging bending moment that comes from fitment of a single insert.
Added Strength
Machined from billets of T6061 Aluminium, the Twin Dogbone Insert is more than strong enough to keep the drivetrain properly located on high power, hard driven cars.
Confirmed Applications.
MQB & MQB 'evo'
2.0 TSI, 1.8 TSI, 2.5 TFSI, 2.0 TDI MODELS
VWR150003/4 see below to identify which type
> | VW Golf 8 | 2020+ |
> | VW Golf 7 & 7.5 | 2013-2020 |
> | VW Passat B8 | 2015+ |
> | VW Arteon | 2017+ |
> | VW T-Roc | 2017+ |
> | VW Tiguan II | 2016+ |
> | VW Jetta / GLI 7 | 2018+ |
> | Audi S3 8Y | 2020+ |
> | Audi A3 8Y | 2020+ |
> | Audi S3 8V | 2013-2020 |
> | Audi A3 8V | 2013-2020 |
> | Audi RS3 2.5 TFSI 8Y | 2021+ |
> | Audi RS3 2.5 TFSI 8V.2 evo | 2017-2020 |
> | Audi RS3 2.5 TFSI 8V | 2015-2017 |
> | Audi TT 3 8S | 2014+ |
> | Audi TTRS 2.5 TFSI 8S | 2017+ |
> | Audi SQ2 | 2018+ |
> | Audi RSQ3 F3 | 2019+ |
> | Cupra Leon IV FW | 2020+ |
> | SEAT Leon III Cupra 5F | 2014-2020 |
> | Cupra Formentor VZ5 2.5 TFSI | 2020+ |
> | Cupra Formentor | 2020+ |
> | Cupra Ateca | 2018+ |
> | Skoda Octavia IV NX | 2020+ |
> | Skoda Octavia III 5E | 2014-2020 |
> | Skoda Superb III 3V | 2015+ |
> | Skoda Kodiaq vRS | 2018+ |
Select your
correct version.
The factory mount comes in two version across MQB models. To ensure fitment on your vehicle, please visually verify the mount you have, then select the correct insert below:
-
OE part: 5Q0 198 037 A – You’ll require the Version 1 Insert
-
OE part: 5Q0 198 037 F – You’ll require the Version 2 Insert
We recommend a visual check to make certain you have the right version:
Version One
A near-circular central hole within the mount.
VWR150003
Or....
Version Two
A triangular central
void inside the mount.
VWR150004
Why fit the
Twin Dogbone Insert?
Why not just fit a single insert?
After all, many companies offer either the upper or the lower mount insert alone. We advise very strongly against fitting just one insert. With a single insert, the twisting moment force on the mount becomes significant, leading to almost-certain failure.
That’s why we only offer the Twin Dogbone Insert, with two billet inserts to keep the forces balanced top and bottom through the mount and remove the risk of twisting forces destroying your insert.
Twin Inserts in mount
Balanced forces; no twisting force.
Single Insert in mount
Unbalanced reaction, twisting moment.
Precision Engineered for
Perfect Performance.
Each Twin Dogbone Insert start life as a billet of T6061 Aluminium, before being precision CNC-machined into shape
Carefully developed for minimal transference of NVH through to the cabin
RacingLine’s trademark black anodised finish for durability over many years
Engineered to slip easily into the voids In factory lower mount
Easy, straightforward installation designed to be fitted without subframe removal takes minutes
Other products
to set your pulse racing.
ADJUSTABLE DROP LINKS
If you've lowered your car, the VWR Adjustable Drop Links allow you to readjust the preload on your anti roll bar and add precision to handling response.
Simply the ultimate suspension kit. Sharing most components with our Full Race kits, they feature full coilover layout with shortened aluminium bodies.
TRACKSPORT SUSPENSION
STUD & NUT KIT
Make swapping wheels easy with our beautiful lightweight stud and nut conversion kit.
